User Guide

Programming #

The NORVI IIOT-AE01-T has a mini USB Port for serial connection with the SoC for programming. Any ESP32-supported programming IDE can be used to program the controller. Follow this Guide to programming NORVI ESP32 controllers with Arduino IDE.

SoC: ESP32-WROOM32
Programming Port: USB UART

Digital Inputs #

Wiring Digital Inputs #

Programming Digital Inputs #

Reading the relevant GPIO of the ESP32 gives the value of the Digital Input. When the inputs are in the OFF state, the GPIO goes HIGH, and when the input is in the ON stage, the GPIO goes LOW.

Refer to the GPIO allocation table in the Datasheet the digital input GPIO.

#define INPUT1 18 
void setup() { 
   Serial.begin(115200); 
   Serial.println("Device Starting"); 

   pinMode(INPUT1, INPUT); 
} 
void loop() { 
   Serial.print(digitalRead(INPUT1));
   Serial.println(""); 
   delay(500); 
}

Transistor Output #

Wiring Transistor Outputs #

Programming Transistor Outputs  #

Reading the relevant GPIO of the ESP32 gives the value of the relay or transistor output.  Refer to the GPIO allocation table in the Datasheet for the relay/transistor output GPIO.

#define OUTPUT1 14 
void setup() { 
   Serial.begin(115200); 
   Serial.println("Device Starting"); 

   pinMode(OUTPUT1 , OUTPUT); 
} 
void loop() { 
   digitalWrite(OUTPUT1, HIGH); 
   delay(500); 
   digitalWrite(OUTPUT1, LOW); 
   delay(500); 

   Serial.println(""); 
   delay(500); 
}

RS-485 communication #

RS-485 Wiring #

Driver	MAX485
UART RX	GPIO3
UART TX	GPIO1
Flow Control	GPIO4

Programming RS-485 #

The UART Connections of the RS-485 of the NORVI IIOT AE01 series are shared with the UART connections of the USB Serial.

#define RS485_FC 4 

void setup() { 
   Serial.begin(115200); 
   Serial.println("Device Starting"); 

   pinMode(RS485_FC, OUTPUT); 
} 
void loop() { 
digitalWrite(RS485_FC, HIGH); // Turns on Transmitter Mode    
Serial.println("RS-485 Sending"); 

   delay(500); 
}

Built-in OLED Display #

Display driver	SSD1306
Communication	I2C
Module Address	0x3C
Resolution	128 x 64

Refer to the GPIO allocation table in the datasheet for the I2C GPIO of the OLED Display.

Library supported by the Adafruit_SSD0306 Library.

Wire.begin (SDA, SCL) is required to initialize I2C on correct pins

Programming OLED Display #

#include <SPI.h> 
#include <Wire.h> 
#include <Adafruit_GFX.h> 
#include <Adafruit_SSD1306.h> 

#define SCREEN_WIDTH 128 // OLED display width, in pixels 
#define SCREEN_HEIGHT 64 // OLED display height, in pixels 

// Declaration for an SSD1306 display connected to I2C (SDA, SCL pins) 
#define OLED_RESET -1 // Reset pin # (or -1 if sharing Arduino reset pin) Adafruit_SSD1306 display(SCREEN_WIDTH, SCREEN_HEIGHT, &Wire, OLED_RESET); 
void setup() { 
   Wire.begin(16,17); 
   if(!display.begin(SSD1306_SWITCHCAPVCC, 0x3C)) { 
   // Address 0x3C for 128x64 Serial.println(F("SSD1306 allocation failed")); 
      for(;;); // Don't proceed, loop forever 
} 

   // Show initial display buffer contents on the screen –
   // the library initializes this with an Adafruit splash screen.    
   display.display(); delay(2000); // Pause for 2 seconds 
} 
void loop() { 
}

Built-in Buttons #

Read mode	ADC (Analog to Digital Conversion)
Analog IO	GPIO32

Programming Buttons #

#define buttonPin 32
int  buttonState = 0;

void setup() {
 
  Serial.begin(9600);                             
  pinMode(buttonPin,INPUT);
}
void loop() { 
  Serial.print("Button: ");
  buttonState = analogRead(buttonPin);
  delay(50);
  Serial.print(analogRead(buttonPin));
  Serial.print("\tAnalog: ");
  delay(1000);
}